NF EN ISO 11297-3

NF EN ISO 11297-3

October 2018
Standard Current

Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 3 : lining with close-fit pipes

This document, in conjunction with ISO 11297‑1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of underground drainage and sewerage networks under pressure. It applies to pipes and fittings, as manufactured, as well as to the installed lining system. It is applicable to polyethylene (PE) pipes of either solid wall single layer or co-extruded layer construction, which is reduced in the factory or on site to provide a close-fitting independent or interactive pressure pipe liner, as well as associated fittings and joints for the construction of the lining system. It is not applicable to PE coated pipes having a peelable, contiguous, thermoplastic additional layer on the outside of the pipe. It is applicable to PE pipes, fittings and assemblies intended to be used at an operating temperature of 20 °C as the reference temperature. NOTE For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see ISO 4427‑1:2007, Annex A.

See more
View the extract
Main informations

Collections

National standards and national normative documents

Publication date

October 2018

Number of pages

28 p.

Reference

NF EN ISO 11297-3

ICS Codes

23.040.20   Plastics pipes
23.040.45   Plastics fittings
91.140.80   Drainage systems
93.030   External sewage systems

Classification index

P16-378-3

Print number

1

International kinship

ISO 11297-3:2018

European kinship

EN ISO 11297-3:2018
Sumary
Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 3 : lining with close-fit pipes

This document, in conjunction with ISO 11297‑1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of underground drainage and sewerage networks under pressure.

It applies to pipes and fittings, as manufactured, as well as to the installed lining system. It is applicable to polyethylene (PE) pipes of either solid wall single layer or co-extruded layer construction, which is reduced in the factory or on site to provide a close-fitting independent or interactive pressure pipe liner, as well as associated fittings and joints for the construction of the lining system. It is not applicable to PE coated pipes having a peelable, contiguous, thermoplastic additional layer on the outside of the pipe.

It is applicable to PE pipes, fittings and assemblies intended to be used at an operating temperature of 20 °C as the reference temperature.

NOTE For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see ISO 4427‑1:2007, Annex A.

Replaced standards (1)
NF EN ISO 11297-3
August 2013
Standard Cancelled
Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 3 : lining with close-fit pipes

<p>ISO 11297-3:2013, in conjunction with ISO 11297-1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of underground drainage and sewerage networks under pressure. It is applicable to pipes and fittings, as manufactured, as well as to the installed lining system. It is applicable to polyethylene (PE) pipe for both independent and interactive pressure pipe liners as well as associated fittings and joints for the construction of the lining system.</p>

Table of contents
View the extract
  • Avant-propos
  • 1 Domaine d'application
  • 2 Références normatives
  • 3 Termes et définitions
  • 4 Symboles et abréviations
  • 5 Tuyaux au stade "M"
  • 6 Raccords au stade "M"
  • 7 Accessoires
  • 8 Aptitude à l'emploi du système de rénovation installé au stade "I"
  • 9 Pratique d'installation
  • Annexe A (normative) Tuyau en polyéthylène (PE) plié en usine, rétabli à son état initial à chaud - Détermination de la capacité de mémoire
  • Bibliographie
What is the Redline format?
The Redline + service - standards comparator allows you to easily and simply identify major changes between the current standard and its last canceled version.

At a glance, you will be able to identify the additions, deletions or modifications to a text, table, figure and formula.
At a glance, you will be able to identify the additions, deletions or modifications to a text, table, figure and formula

The Redlines + service is offered to you on the collection of French standards in force, in French language and in HTML and PDF format.

For an overview of the service, click on View a standard in redline format
Need to identify, monitor and decipher standards?

COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.

Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!

Request your free, no-obligation live demo

I discover COBAZ