NF EN ISO 10211
- Consult online for free
- Consult the entire collection of French and European standards for free in the regional delegations of the AFNOR Group by clicking here
Thermal bridges in building construction - Heat flows and surface temperatures - Detailed calculations
ISO 10211:2017 sets out the specifications for a three-dimensional and a two-dimensional geometrical model of a thermal bridge for the numerical calculation of - heat flows, in order to assess the overall heat loss from a building or part of it, and - minimum surface temperatures, in order to assess the risk of surface condensation. These specifications include the geometrical boundaries and subdivisions of the model, the thermal boundary conditions, and the thermal values and relationships to be used. ISO 10211:2017 is based upon the following assumptions: - all physical properties are independent of temperature; - there are no heat sources within the building element. ISO 10211:2017 can also be used for the derivation of linear and point thermal transmittances and of surface temperature factors. NOTE Table 1 in the Introduction shows the relative position of ISO 10211:2017 within the set of EPB standards in the context of the modular structure as set out in ISO 52000-1.
ISO 10211:2017 sets out the specifications for a three-dimensional and a two-dimensional geometrical model of a thermal bridge for the numerical calculation of
- heat flows, in order to assess the overall heat loss from a building or part of it, and
- minimum surface temperatures, in order to assess the risk of surface condensation.
These specifications include the geometrical boundaries and subdivisions of the model, the thermal boundary conditions, and the thermal values and relationships to be used.
ISO 10211:2017 is based upon the following assumptions:
- all physical properties are independent of temperature;
- there are no heat sources within the building element.
ISO 10211:2017 can also be used for the derivation of linear and point thermal transmittances and of surface temperature factors.
NOTE Table 1 in the Introduction shows the relative position of ISO 10211:2017 within the set of EPB standards in the context of the modular structure as set out in ISO 52000-1.
Le présent document établit les spécifications sur les flux thermiques tridimensionnels ou bidimensionnels (qui peuvent être déterminés avec précision en utilisant les méthodes détaillées de calcul numérique décrites) d'un pont thermique pour le calcul numérique, des flux thermiques et des températures superficielles minimales, afin d'évaluer le risque de condensation superficielle.
- Avant-propos
-
1
-
2 Références normatives
-
3 Termes et définitions
-
4 Symboles et indices
-
5 Description de la méthode
-
6 Données de sortie et données d'entrée
-
7 Modélisation de la construction
-
8 Spécifications des données d'entrée
-
9 Méthode de calcul
-
10 Détermination des coefficients de couplage thermique et des flux thermiques issus des calculs 3-D
-
11 Calculs utilisant les coefficients ponctuel et linéique de transmission thermique à partir de calculs 3-D
-
12 Détermination du coefficient de couplage thermique, du flux thermique et du coefficient linéique de transmission thermique à partir de calculs 2-D
-
13 Détermination de la température à la surface intérieure
-
14 Rapport
- Annexe A (normative) Données d'entrée et fiche technique pour la sélection de la méthode - Modèle
- Annexe C (normative) Validation des méthodes de calcul
- Annexe D (normative) Exemples de détermination des coefficients linéiques et ponctuels de transmission thermique
- Annexe E (normative) Détermination des valeurs du coefficient de couplage thermique et du facteur de pondération de la température pour plus de deux températures aux limites
- Annexe B (informative) Données d'entrée et fiche technique pour la sélection de la méthode - Choix par défaut
- Bibliographie
The Requirements department helps you quickly locate within the normative text:
- mandatory clauses to satisfy,
- non-essential but useful clauses to know, such as permissions and recommendations.
The identification of these types of clauses is based on the document “ISO / IEC Directives, Part 2 - Principles and rules of structure and drafting of ISO documents ”as well as on a constantly enriched list of verbal forms.
With Requirements, quickly access the main part of the normative text!
At a glance, you will be able to identify the additions, deletions or modifications to a text, table, figure and formula.
The Redlines + service is offered to you on the collection of French standards in force, in French language and in HTML and PDF format.
For an overview of the service, click on View a standard in redline format
COBAZ is the simple and effective solution to meet the normative needs related to your activity, in France and abroad.
Available by subscription, CObaz is THE modular solution to compose according to your needs today and tomorrow. Quickly discover CObaz!
Request your free, no-obligation live demo
I discover COBAZ